JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 17y 15d Gender: Male Location: Adelaide Posted 03/09/14 04:04 AM Share Posted 03/09/14 04:04 AM It pivots and lifts off from flush aprox 19mm at the highest mechanically but its all relevant to commanded D/C and at full rpm its usually back to the "seated" position to command full flow across the rear wheel Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1496897 Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 17y 7m 19d Gender: Male Location: Perth Posted 03/09/14 04:37 AM Share Posted 03/09/14 04:37 AM With a user name like that it sounds like you have already had a "PORT" job....... 1 Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1496899 Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 17y 15d Gender: Male Location: Adelaide Posted 03/09/14 10:17 AM Share Posted 03/09/14 10:17 AM Could be worse Could have the same name as u but spelt correctly Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1496966 Share on other sites More sharing options...
Bomber Carnage on the Garage Floor Donating Members 3,994 Member For: 15y 1m 4d Gender: Male Location: Gold Coast Posted 03/09/14 11:01 PM Share Posted 03/09/14 11:01 PM seated at full rpm? Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1497029 Share on other sites More sharing options...
ratter Member 6,793 Member For: 19y 19d Gender: Male Location: @ my laptop Posted 03/09/14 11:49 PM Share Posted 03/09/14 11:49 PM yes dependent on set up and what boost is being run Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1497033 Share on other sites More sharing options...
Marc McDonald Member 18 Member For: 15y 6m 29d Posted 13/07/15 09:50 AM Share Posted 13/07/15 09:50 AM What studs do you guys recommend replacing the 4 that connect the turbo to the manifold with? I completely rounded one and used a nut splitter to get it off so was thinking of getting a set of these?http://gcg.com.au/turbo-parts/studs-nuts/stud-nut-kit-m10x1-5x40-4-detailDo the job? Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1553558 Share on other sites More sharing options...
Bizkets is Drunk? Too heavy needs boost Member 5,929 Member For: 11y 10m 9d Gender: Male Location: Adelaide Posted 13/07/15 10:40 AM Share Posted 13/07/15 10:40 AM Turbo Accessories, Fastners - MTQ Sonic - Sonic Performancehttp://www.sonicperformance.com.au/Turbo-Accessories/Fastners/pl.phpThird set down I believe. Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1553580 Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 29,551 Member For: 17y 2m 5d Gender: Male Location: Melbourne Posted 13/07/15 10:52 AM Share Posted 13/07/15 10:52 AM (edited) that'll get you the nuts, but you would want different studs...The studs are M10x1.25 on one side and M10x1.5 on the other. The 1.5 end goes into the manifold and the 1.25 allows for a finer thread and more torque on the turbo side.EDIT: these ->http://www.ebay.com.au/itm/TURBO-EXHAUST-STUD-NUT-SET-M10-X-1-25-M10-X-1-5-4-PACK-/151390627050with either stage 8 fasteners -> http://gcg.com.au/turbo-parts/stage-8-fasteners/stage-8-fasteners-m10x1-25-nut-lock-kit-detailor nordloc washers. -> http://www.ebay.com.au/itm/1-Stuck-NORD-LOCK-NL10-Keilsicherungsscheiben-M10-Sicherungsscheibe-NordLock-/151257003664 Edited 13/07/15 10:57 AM by k31th 1 Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1553588 Share on other sites More sharing options...
Marc McDonald Member 18 Member For: 15y 6m 29d Posted 13/07/15 10:54 AM Share Posted 13/07/15 10:54 AM (edited) Turbo Accessories, Fastners - MTQ Sonic - Sonic Performancehttp://www.sonicperformance.com.au/Turbo-Accessories/Fastners/pl.phpThird set down I believe.Cheers mate looks perfect!Thanks K31th I'll grab the other studs too, thanks! Edited 13/07/15 10:56 AM by Marc McDonald Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1553589 Share on other sites More sharing options...
Bizkets is Drunk? Too heavy needs boost Member 5,929 Member For: 11y 10m 9d Gender: Male Location: Adelaide Posted 13/07/15 11:00 AM Share Posted 13/07/15 11:00 AM New gasket would be the go to. Link to comment https://www.fordxr6turbo.com/forum/topic/43547-removal-of-turbo-in-preperation-of-porting-and-valve-mod-part-ii/page/5/#findComment-1553592 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now