Jump to content

Recommended Posts

  • Member
  • Member For: 18y 1m 2d
Posted

I got extinguisher and bracket from bunnings in a pack labelled as CAMS approved. Screwed the bracket into the plastic trim on the passenger side of the transmission tunnel (basically beside passengers right knee), its not going anywhere and if I need to get rid of it that panel is cheap to replace. A bracket that comes off the seat rails would be ideal but I didnt have the time or skills to sort one out.

  • Replies 33
  • Created
  • Last Reply

Top Posters In This Topic

  • Legacy Donating Member
  • Member For: 19y 5m 10d
  • Gender: Male
  • Location: Caracciola Karussell
Posted (edited)

Mine does block the seat from moving forward BUT I knew it was going to and since the seat rarely moves, it suits me. If on the odd chance someone is in the back, if they whinge, they can walk :)

Excuse the pics. I just had some weird plant in the front and bark and crap went everywhere. Also notice theres $2 hidden under the seat lol. Gives you an idea I guess.

Bah, image shack cracked the poos.

Once photobucket is back online, I'll throw em on there

Edited by Mat
  • Legacy Donating Member
  • Member For: 19y 5m 10d
  • Gender: Male
  • Location: Caracciola Karussell
Posted (edited)

In my WRX the extinguisher sat at an angle in the same spot but in the taxi it sits flat. It sits low enough so that when you sit down, you dont notice its there. Its in an easy to get to spot. If I wanted to remove the trim, I could have had it angled. Apparently the foam or whatever it is in them, removes fingerprints left behind on various surfaces (ie a crime scene...). I do know that we had some guys in high school who emptied several over the ovals and it destroyed the lawn lol.

072.jpg

073.jpg

071.jpg

070.jpg

Definitely needs a good clean!

Edited by Mat
  • Legacy Donating Member
  • Member For: 17y 4m 24d
  • Gender: Male
  • Location: CHCH NZ
Posted

I made a bracket for mine ill post pics tomorrow when I install it

  • 2 weeks later...
  • Legacy Donating Member
  • Member For: 17y 4m 24d
  • Gender: Male
  • Location: CHCH NZ
Posted

Heres the results. I made an alloy bracket to support the bracket and stop the bottle from sliding out. The plastic is a decent grade so shouldnt break. The seat slides over the FE with alot of room to spare.

post-35221-127338634281_thumb.jpg

post-35221-127338635478_thumb.jpg

  • Legacy Donating Member
  • Member For: 21y 4m 4d
Posted

I have one in the boot on the left side...its an ex chaser so im not sure if its a Ford thing or a Police after market thing...if you want photos let me know...

  • Legacy Donating Member
  • Member For: 17y 4m 24d
  • Gender: Male
  • Location: CHCH NZ
Posted (edited)

only problem is you need power to open boot..on the other hand if someone really hits you hard from behind it may rupture the FE...thus saving you a job :buttonit:

Edited by osonvs
  • Legacy Donating Member
  • Member For: 18y 8d
  • Gender: Male
  • Location: port hedland
Posted

I would have to think front passenger side have a lil 1 mounted on the gear box side, that's where most of our work utes are

  • Member
  • Member For: 18y 1m 27d
  • Gender: Male
  • Location: S.E Suburbs!
Posted

16052010831.jpg

16052010830.jpg

This is where I put mine! Guys here have spoken about rear end collisions! I have put it here so that if boot is jammed shut it can still be accessed from either side of the car!

My belief is also if your hit in the back hard enough the boot pops open most of the times!

  • Legacy Donating Member
  • Member For: 17y 4m 24d
  • Gender: Male
  • Location: CHCH NZ
Posted

true, id rather have mine in reach though..just incase..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.



×
×
  • Create New...