Jump to content

Recommended Posts

  • Member
  • Member For: 15y 6m 13d
  • Gender: Male
  • Location: Mackay QLD
Posted

Hey all, I have recently disconnected the stock heat exchanger from my fg xr6t and fit an oil - air cooler. So far all is well, and more to the point... no chance of a milkshake in my gearbox! :) I used the PWR Cooler, got some lines, and a set of fittings from ebay (tried cutting the stock exchanger pipes off but it was to dodgy for my liking) I dont have an auto trans temp gauge however took it to the drags the other weekend, and no problems after 5 consecutive runs. Noticed the oil was a discoloured when installed the cooler, so I am going to get a flush very shortly...

The install itself wasnt too hard, had to relocate the horn, and extend the fog light wiring a little bit... no big deal! Im pleased with the result.

Running stock power levels atm, also I have a 10 inch thermo fan that im am going to fit to the front of my oil cooler, when I can be bothered :headbang2:

This is the PWR cooler I used

1b1019fc.jpg

And the fittings I bought off ebay!

d8ef8524.png

Mounted the cooler under the DS headlight

2f00d15d.jpg

309b31d6.jpg

Used a die grinder and made a few slits in the wheel arch to let the air flow through!

a6318cc6.jpg

Any questions feel free to ask! :)

  • Like 1
  • Waiting for the 1st N/A 12!
  • Legacy Donating Member
  • Member For: 18y 7m 8d
  • Gender: Male
  • Location: Sydney
Posted

Nice one!

I put mine somewhere a little different!

8h0ws.jpg?1

  • Like 2
  • Member
  • Member For: 17y 10m 17d
  • Gender: Male
Posted

Good stuff might attempt it next week . I thought about that second one but wasn't keen on drilling a hole in for 1 of the lines -_-

  • Legacy Donating Member
  • Member For: 15y 2m 14d
  • Gender: Male
  • Location: Surrey Hills, Melbourne
Posted

I put mine somewhere a little different!

8h0ws.jpg?1 [/

Trans looks brand new Matt.

How is it?

  • Waiting for the 1st N/A 12!
  • Legacy Donating Member
  • Member For: 18y 7m 8d
  • Gender: Male
  • Location: Sydney
Posted

I put mine somewhere a little different!

http://I.imgur.com/8h0ws.jpg?1[/

Trans looks brand new Matt.

How is it?

Yeah mate to coming along nicley!

couple of little issues but all seem ok now!

Just waiting one some rear driveline upgrades before I hit the track.

What did you end up doing with your Drive Shafts?

  • Member
  • Member For: 22y 7m 5d
  • Gender: Male
  • Location: Melbourne
Posted

Have you added a fan to it Veva or is it ok like that? What brand cooler? Great spot..

  • Moderating Team
  • Member For: 23y 7m 19d
  • Gender: Male
  • Location: Sydney
Posted

was wondering that too

having air skim across it isnt nearly as effective as air actually being forced through it.

  • RNS10S
  • Legacy Donating Member
  • Member For: 20y 1m 2d
  • Gender: Male
Posted

Air passing over it would be enough to keep it cooler than the factory setup

  • Legacy Donating Member
  • Member For: 15y 2m 14d
  • Gender: Male
  • Location: Surrey Hills, Melbourne
Posted

What did you end up doing with your Drive Shafts?

It's been delayed as Albin can't find a block big enoughto make driveshaft out of. Will be lucky to be back this year. Pointless going back to std temporarily IMO as will just break again at track but will be ok or street use. Might just wait for strong stuff me thinks.

  • Waiting for the 1st N/A 12!
  • Legacy Donating Member
  • Member For: 18y 7m 8d
  • Gender: Male
  • Location: Sydney
Posted (edited)

Have you added a fan to it Veva or is it ok like that? What brand cooler? Great spot..

No fan just a little scoop and some mesh!

Logged temps and she never went over 165 F

Edited by Vevapower

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...