harlee

Even if its just an outlet for hot air, it could lower under bonnet temperatures by over 10°C. Its ideally placed, at the point where the overbonnet airflow sucks hardest (a few inches infront of the windsheild), and its big enough to cover most of the central part of the bonnet.... Rather than directly increasing power, it would alow the engine to make more power in a slightly more idealistic fassion, with the hot air being sucked out more efficiently, giving the cooling system maybe the slightest, oh so slightest, of helping hands.... <{POST_SNAPBACK}> Sorry. On a normal XR8 bonnet there is no wind sucking going on at the back of the bulge. At 120klm's on the freeway, pouring rain, you can watch all the little drops of water dancing around, going no where, on the back of the bulge With the vents it might give it some "flow thru" ventilation, but not much sucking

It's obvious you have never ridden a bike in a jungle of cars, The benefit of loud pipes on a bike is if the car drivers cant see you then as sure as hell they will hear you. And like cars there are a few idiots on bikes out there that ruin it for everybody else.

heidfelt and webber raped him for 2nd and 3rd, what a load of They held a gun to his head and made him wear out his rear tyres did they

Wheel Factory is still there, I was out there today. It shares the shop with QuickFit tyres and Brett ex/service manager pollocks and gregory's is the owner, is a good guy too.

I'm 46 in canberra with a 5 month old BA XR8 insured with nrma.Costs $820 a year for $50,000, just put 18" wheels on - no change to policy,asked about CAI and any type of exhaust and they said no worries, no price change , just let us know if and when you do it and they will update policy

I have seen a guy on ebay selling BA XR6 17" and 18" mag wheels to suit BA and another set with correct offset to fit AU's. They are copies and when I rang the guy to enquire about them he told me they were Enkei copies and you couldn't tell the difference, $1000 for 4 bare rims and $2000 fitted with Nangkangs or something similar, delivered I think ??

years ago I knew a guy who owned a XYGT and unfortunately earned the nickname ankles after his flywheel did a similar thing, one piece went thru the back of the dash and came out near the rhs wiper arm and another piece went thru the floor and hit him in the ?????

I had a BAXR6 n/a and it would flare up to 2000rpm the same as above , after numerous visits to Mcgrath Ford in Canberra they kept telling me it's within spec's The same thing they are telling me now that my BAXR8 auto can take anything up to 15 seconds to find reverse. What a load of

go to www.intunemotorsport.com.au they sell all the goodies for BA XR8's including stripe kits, etc

Its being released in australia later this year and this is cheap advertising.Also it has the v8 engine that cuts out 4 cylinders when cruising to save on fuel

Exact same article in todays daily telegraph

You had best go and have another look

I dont believe it a thread where everybody agrees, woohoo. Shoot the little #uckers right between the eyes with rubber bullets then see if they still want to throw rocks.

All you guys are sounding like the whingeing b**ches from the ls1 forum.Has anybody got any proof the ls1 qiksmurf is the same as the xr6 qiksmurf. I thought it was innocent until PROVEN guilty.

:lol: Mark Skaife is a wa*ker Do you realise Skaife's No 2 driver Todd Kelly was driving Skaife's car at the Indy races, when they got caught and got penalised the amount Skaife and Perkins demanded be introduced after the Ambrose affair. How ironic. Skaife suck my

story about the turbo territory and the typhoon in todays motoring section in daily telegragh paper

:lol: very clever

good luck, mine cost the nrma $5500 me $450 about 3 months ago,it was done from headlight to tail light.not a straight line but up and down, round and round.But as they say there is always someone worse off than you, I know anther guy had to get a complete respray when they did every panel on his XR8. And all this in sunny downtown canberra

I had this problem in a AU sedan, everytime I washed the car or it rained I would get half a cup of water in the right front corner of the boot, the conclusion the ford dealer came too was that where the rear quarter joined the main shell underneath the rear window on the rhs wasn't spot welded properly and there fix was to cover the seam in about fifty gallons of some particular type of silastic/glue/crap stuff, it fixed it the leak but not the problem good luck

Here in canberra you can get a aftermarket one fitted for around $240

Happy Birthday FordXR6Turbo.com

good piccys mr turbo

thanks for that

I was trying to upload foto of PBR brake upgrade containing, f+r slotted rotors, f+r performance calypers and braided brake lines to suit AU and BA fords and the usual dunnydores in the latest repco cat.Price FROM $2324.00. On sale from7/10/04 until 24/10/04 so there