SHOCK Team Grandpa Donating Members 1,921 Member For: 19y 9d Gender: Male Location: Hunter Valley Posted 02/06/06 11:22 AM Share Posted 02/06/06 11:22 AM Got a FPV pod and gauges for the T finally.Can someone tell me the best way to remove the old plate on the T to replace it with the new pod. Are there screws? Velvet sledgehammer required???AlsoNot having a f*ckn clue about auto wiring, where can I go in Brisy to get these wired up professionally. Not knocking any back yard boys(my brother is one and he could rebuild my motor and wire this up blindfolded) I just like the warranty side of things.... cheersJohno Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/ Share on other sites More sharing options...
SHOCK Team Grandpa Donating Members 1,921 Member For: 19y 9d Gender: Male Location: Hunter Valley Posted 02/06/06 12:51 PM Author Share Posted 02/06/06 12:51 PM Does this mean I'm not in the 'in crowd' either, its been nearly 1.5 hours... Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/#findComment-389829 Share on other sites More sharing options...
T007 Woooooooosh Donating Members 734 Member For: 19y 10m 2d Location: Sydney Posted 02/06/06 12:55 PM Share Posted 02/06/06 12:55 PM Three slide clips hold it in place Just pull it straight up Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/#findComment-389832 Share on other sites More sharing options...
SHOCK Team Grandpa Donating Members 1,921 Member For: 19y 9d Gender: Male Location: Hunter Valley Posted 02/06/06 01:00 PM Author Share Posted 02/06/06 01:00 PM cheers Turb, wasnt sure if it was the same as the FPV clips. Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/#findComment-389834 Share on other sites More sharing options...
LTSBGY Member 259 Member For: 19y 3m 23d Posted 02/06/06 01:39 PM Share Posted 02/06/06 01:39 PM (edited) Dumb questions but I just purchased the typhoon gauge holder today? How are the front bezels meant to go on? glue of some sort coz they dont clip on? I recieved 4 thin strips of the black tape things, what are they used for?ThanxNesh Edited 02/06/06 01:54 PM by nesh Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/#findComment-389842 Share on other sites More sharing options...
ExAreSix TRAITOR Member 1,063 Member For: 22y 6m 20d Gender: Male Location: Townsville, NQ Posted 02/06/06 09:25 PM Share Posted 02/06/06 09:25 PM Three slide clips hold it in place Just pull it straight up←Not quite. Two clips, at the front. You need to lift the front corner (Windscreen end... duh) first.The rear edge (top of stereo surround... duh) is located with lugs. If you pull that edge straight up you'll snap bits. Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/#findComment-389875 Share on other sites More sharing options...
SHOCK Team Grandpa Donating Members 1,921 Member For: 19y 9d Gender: Male Location: Hunter Valley Posted 02/06/06 10:30 PM Author Share Posted 02/06/06 10:30 PM Dumb questions but I just purchased the typhoon gauge holder today? How are the front bezels meant to go on? glue of some sort coz they dont clip on? I recieved 4 thin strips of the black tape things, what are they used for?ThanxNesh←I didnt get any of these, mine was assembled and a Genuine FPV model.There are two star head cap screws for each holding the gauge holders down with only two yellow clips. Will get some pics later Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/#findComment-389879 Share on other sites More sharing options...
tab Sucker Moderating Team 32,303 Member For: 21y 15d Gender: Male Location: Brisbane Posted 02/06/06 10:46 PM Share Posted 02/06/06 10:46 PM Does this mean I'm not in the 'in crowd' either, its been nearly 1.5 hours... ← Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/#findComment-389882 Share on other sites More sharing options...
SHOCK Team Grandpa Donating Members 1,921 Member For: 19y 9d Gender: Male Location: Hunter Valley Posted 02/06/06 11:55 PM Author Share Posted 02/06/06 11:55 PM Thanks Tab, I'll slept better tonight knowing I cant match it with you champ, u da man Back to topic.....here are some pics I just took to help us amateurs, I only have two yellow clips, will this clip straight in to the T dash Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/#findComment-389891 Share on other sites More sharing options...
Hornblower Member 50 Member For: 22y 3m 10d Location: Spit Junction NSW Posted 04/06/06 06:33 AM Share Posted 04/06/06 06:33 AM Yes, that will click straight in (give it a good push) but first slide the little lugs into position at front (front meaning the icc side). Link to comment https://www.fordxr6turbo.com/forum/topic/25902-gauge-thread-no-41572/#findComment-390304 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now