violetpop Silver Donating Members 436 Member For: 4y 4m 11d Posted 01/04/21 01:35 AM Author Share Posted 01/04/21 01:35 AM Just got word back from dominator 3 steps 100ft pounds 'just like arp'. Good to go Link to comment Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 15y 10m 19d Gender: Male Location: Adelaide Posted 01/04/21 03:51 AM Share Posted 01/04/21 03:51 AM Do not go over 100ftlb unless you have OS washers then you can wind most studs upto the 120ftlb zone without issues on M12’s 1 Link to comment Share on other sites More sharing options...
violetpop Silver Donating Members 436 Member For: 4y 4m 11d Posted 01/04/21 10:32 AM Author Share Posted 01/04/21 10:32 AM Couldn't wait so got the car to the shop after work and got a jump start.. All the good stuff going on. Going to try leave the turbo manifold and everything in place possibly held back by some rope and its pretty much inlet manifold out of the way, cams and head off. Might run some cheapo oil through it for 15 minutes and aim to get rid of as much crap as possible. Link to comment Share on other sites More sharing options...
Puffwagon Puff Gold Donating Members 15,117 Member For: 9y 2m 21d Gender: Male Location: South Australia Posted 01/04/21 10:43 AM Share Posted 01/04/21 10:43 AM That's a lot of water in there man. Is there evidence on the gasket where it leaked or have you found a crack in the head? Is there something else that has failed like an oil cooler? 1 Link to comment Share on other sites More sharing options...
violetpop Silver Donating Members 436 Member For: 4y 4m 11d Posted 01/04/21 10:47 AM Author Share Posted 01/04/21 10:47 AM Yet to get the head off to check.. A crack in the head was my gut feeling. All I could see was water coming into number 5 and a miss. When I last checked the oil, it was still gold. The short drive here and I checked it again and it was milky. No oil cooler on this engine so a close look at the head and gasket when it comes out. 1 Link to comment Share on other sites More sharing options...
JETURBO ...JD TUNING ADELAIDE... Gold Donating Members 23,708 Member For: 15y 10m 19d Gender: Male Location: Adelaide Posted 01/04/21 10:56 AM Share Posted 01/04/21 10:56 AM Honestly.... Just pull the engine and get it on a stand, it’s faster & easier mate but that’s fisted ! 1 Link to comment Share on other sites More sharing options...
violetpop Silver Donating Members 436 Member For: 4y 4m 11d Posted 01/04/21 11:16 AM Author Share Posted 01/04/21 11:16 AM You're right about getting the engine out because I also need to look at the trans leak but time is limited and this is the best option for me atm.. Still a hoist is better than straight up floor work. Link to comment Share on other sites More sharing options...
violetpop Silver Donating Members 436 Member For: 4y 4m 11d Posted 01/04/21 09:18 PM Author Share Posted 01/04/21 09:18 PM Good morning everyone! Early start and whipped the head off. Nothing overly obvious from what I can see unless I'm missing something. Going to clean up the head and check if its straight next up. Link to comment Share on other sites More sharing options...
Tom Tucker Donating Members 614 Member For: 4y 9m 20d Posted 02/04/21 01:12 AM Share Posted 02/04/21 01:12 AM The mystery continues! Good job getting amongst it 1 Link to comment Share on other sites More sharing options...
adams355 Member 529 Member For: 6y 11m 18d Gender: Male Location: Brisbane Posted 02/04/21 05:26 AM Share Posted 02/04/21 05:26 AM If it's not the head I reckon you have found it, doesn't have to 'blown'. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now