OZYWALKER XR50T Gold Donating Members 2,795 Member For: 10y 11m 21d Gender: Male Location: Western Sydney Posted 30/05/17 09:33 AM Share Posted 30/05/17 09:33 AM Fronts will clear fine, may need to roll the guards depending on how low the car is.Rears are a different story, need measurements of the tray and chassis from a wheel with a known offset. Link to comment Share on other sites More sharing options...
peps New Member 18 Member For: 9y 4m 4d Posted 30/05/17 09:48 AM Author Share Posted 30/05/17 09:48 AM I will pull the rears back off tomorrow and get some more measurements. anything I should look out for? Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 16y 5m 27d Gender: Male Location: Perth Posted 30/05/17 10:44 AM Share Posted 30/05/17 10:44 AM Offset and backspace are two completely different things Link to comment Share on other sites More sharing options...
bossmang FREAKY Donating Members 12,403 Member For: 14y 3m 28d Gender: Male Location: Melbourne Posted 30/05/17 11:03 AM Share Posted 30/05/17 11:03 AM http://letmegooglethat.com/?q=offset+vs+backspace Link to comment Share on other sites More sharing options...
peps New Member 18 Member For: 9y 4m 4d Posted 01/06/17 11:16 AM Author Share Posted 01/06/17 11:16 AM (edited) After a re-measure today of the rears, it will maybe just fit. I had a 17inch rim handy with no tyre; Measuring along the top of the 17's I need 2mm more clearance to the flexible part of the break line.. once I go to 18 it should be 0-1mm clearance, So how hard is it to bend the break line while still on the car. everything else clears by 10mm at 17inch and clearance will increase the larger the wheel.. Edited 01/06/17 11:25 AM by peps Link to comment Share on other sites More sharing options...
OZYWALKER XR50T Gold Donating Members 2,795 Member For: 10y 11m 21d Gender: Male Location: Western Sydney Posted 01/06/17 11:25 AM Share Posted 01/06/17 11:25 AM They can bend a bit, I found the aftermarket braided lines have a bit more give in them. Link to comment Share on other sites More sharing options...
peps New Member 18 Member For: 9y 4m 4d Posted 01/06/17 12:54 PM Author Share Posted 01/06/17 12:54 PM is it right to bend whilst on the car? or better to pull it off and do it properly? Link to comment Share on other sites More sharing options...
4321 Bronze Donating Members 257 Member For: 10y 27d Posted 01/06/17 09:00 PM Share Posted 01/06/17 09:00 PM The steel lines are easy to bend (depending on how far you intend ) Just push on them with your palm & they bend quiet easily but if your after major movement take them off & use a pipe bender Link to comment Share on other sites More sharing options...
peps New Member 18 Member For: 9y 4m 4d Posted 02/06/17 06:09 AM Author Share Posted 02/06/17 06:09 AM http://www.rimsntires.com/specspro.jsp I just found this and its making my life easier, it might help someone else later. Link to comment Share on other sites More sharing options...
MBAF Bronze Donating Members 2,156 Member For: 7y 8m 8d Posted 02/06/17 08:00 AM Share Posted 02/06/17 08:00 AM I may have missed it but what tyr3 size are you wanting to run? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now