Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 18y 6m 25d Gender: Male Location: Perth Posted 29/05/17 11:00 AM Share Posted 29/05/17 11:00 AM I hadn't seen that question, if the thread is munted and jams before compressing the gasket to the point it'll seal then the only fixed is to fix the thread. Otherwise a sly washer on the bolt may give enough compression before it jams. Either way paper gaskets in an area that sees as much heat as a turbo drain is testicles and a high temp oring arrangement will always be better 1 Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 28,283 Member For: 16y 8d Gender: Male Location: Melbourne Posted 29/05/17 11:02 AM Share Posted 29/05/17 11:02 AM Fair enough. Thanks for that I'll give the washer a try - not optimistic haha. Link to comment Share on other sites More sharing options...
eff xr6t Member 569 Member For: 10y 6m 19d Posted 29/05/17 11:35 AM Share Posted 29/05/17 11:35 AM Should be able to helicoil easily in that area? Easy fix being a small bolt in aluminium also more room there on a B series k frame then my E series. Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 28,283 Member For: 16y 8d Gender: Male Location: Melbourne Posted 29/05/17 11:40 AM Share Posted 29/05/17 11:40 AM yeah, there's a bit of room, if you can maneuver around the hot side pipe unfortunately I don't own a helicoil kit. Link to comment Share on other sites More sharing options...
arronm Dropping a turd Gold Donating Members 9,520 Member For: 16y 5m 22d Gender: Male Location: Perth Posted 29/05/17 11:43 AM Share Posted 29/05/17 11:43 AM (edited) You buy them at the shops crack boy. I look at cracks all day. And sometimes at night Edited 29/05/17 11:46 AM by arronm Link to comment Share on other sites More sharing options...
bupalooga Silver Donating Members 255 Member For: 11y 6m 12d Gender: Male Location: Griffith NSW Posted 29/05/17 11:43 AM Share Posted 29/05/17 11:43 AM Forgot to post what I got done over the weekend:Rear wheal bearing replaced, thanks heaps to bamk2f6tornado for very accurate instructions for the procedure. Cold side & core from 2nd hand snail attached to the old modified hot side & wastegate & remounted with new studs. Air system for horn & bagged trailer all finished & works posh as! Switches to control it all from the cabin. It's a bit hard to show the horns cause they're crammed right up under the tray, so these are the best pics I can get. & finished up the weekend with a fully hectic clean & Polish. Sent from my fancy pansy touchy screeny phoney using a Tapatalka appliacationa 5 Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 28,283 Member For: 16y 8d Gender: Male Location: Melbourne Posted 29/05/17 11:46 AM Share Posted 29/05/17 11:46 AM 1 minute ago, arronm said: You buy them at the shops crack boy. derp... it would cost me less to get the mobile thread guy around to fix it than it would to buy a helicoil kit. Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 18y 6m 25d Gender: Male Location: Perth Posted 29/05/17 11:46 AM Share Posted 29/05/17 11:46 AM Honk.... Link to comment Share on other sites More sharing options...
Ralph Wiggum Moar Powar Babeh Lifetime Members 19,323 Member For: 18y 6m 25d Gender: Male Location: Perth Posted 29/05/17 11:54 AM Share Posted 29/05/17 11:54 AM Is the munted thread in the sump? If so bulk room to helicoil it. Plug the drain hole with rag first and don't drill all the way through. The holes are blind from the factory. Link to comment Share on other sites More sharing options...
k31th less WHY; more WOT Site Developer 28,283 Member For: 16y 8d Gender: Male Location: Melbourne Posted 29/05/17 11:55 AM Share Posted 29/05/17 11:55 AM yeah, it's in the sump. cheers guys, appreciate it Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now