Jump to content

What Did You Do To Your Car Today?


Henz

Recommended Posts

  • To Loud
  • Gold Donating Members
  • Member For: 12y 3m 28d
  • Gender: Male
  • Location: WA, Perth

It looks mint with the leather seats.....

Maybe change the gear boot to a cream leather one and it would look better??

 

Did you put cv grease on the gear knob too see what black would look like?

Edited by masda74
Link to comment
Share on other sites

  • Bronze Donating Members
  • Member For: 10y 3m 26d
  • Gender: Male
  • Location: Rockhampton Qld

Been a quiet week due to all this water about. Got a bit done today

Trimmed the inner tub lip and hammed the lip Flat. Should allow for 295 wide rubber hopefully. (Pic pre paint)

Shocks installed with new bushes

Put the tub back on then started on this fuel system. Ran a few lines then called time for a beer. Hopefully get it finished up this week. The urge for a skid is strengthening c3e2cd58f23a3d444a920456093ae90a.jpg7188535d519a424a8e1edd9aac017a0d.jpg02c1b39071440b69e93196e04d7c4636.jpgb672318770443ca28d3832eada3da193.jpg

  • Like 4
Link to comment
Share on other sites

  • Bronze Donating Members
  • Member For: 10y 3m 26d
  • Gender: Male
  • Location: Rockhampton Qld

Got the tub all bolted in. Wires n fuel lines all ran. Nutserted all the bolts that hold the tub liner in and hardlid on for a neater finish. Have some nice stainless eyelets go in there for easier load restraint.
Pro tip- when making a cheap nutsert tool make sure you don't use a sharp bit of steel haha. Almost spent my arvo at the doctors. Hopefuly have it finished tomorrow fingers crossed 5a1605a2d0ccda88a844a09ed7b58c69.jpg945e06d0e2ae1c903cfb8ed38fc2e00f.jpg3e4ed7561ba49ee40429389f4532653f.jpg23d1dc79d0315c509e945e8d9094e1e1.jpg8688935338879a71293832e4c8b539c0.jpg

  • Like 3
Link to comment
Share on other sites

  • Bronze Donating Members
  • Member For: 10y 3m 26d
  • Gender: Male
  • Location: Rockhampton Qld

Got the Ute finished today. Finished up all the wiring. Both the 044 and the walbro intank now have there own relays triggered from the stock pump wiring (inertia/roll-over switch will shut pumps off still).
Going to put a cover over the relays eventually by won't really matter once the hardlid goes on.
Gave it a much needed wash.
Had 1 minor f*ck up. I was wondering why the Ute wasnt idling and 044 was making bulk noise and stuttering. After much confusion I ended up having the feed/return lines back to front on the chassis rails. So swapped em round and hooked it all back up and it ran perfect.
Deleted the stock filter so now it just has the earls one in the tray. Used a male and a female 5/16th hardline adaptor.

And most importantly took it for a spin! Been atleast a month since its seen boost. The shocks are much nicer now softened up. The swaybar makes a noticeable different, feels much more positive.
Tramp rods work mint. No binding noises. No skids yet but gave it a stab in second and it just lit them up with no tramp what so ever. Beer time 22ee4e6d9e9fe617a202c7f8eb94e284.jpgaaebfc913f0e53583ddbf23412cc042c.jpg4ba4997be55ca7836c4b86d870e6a6f8.jpg

  • Like 9
Link to comment
Share on other sites

  • Silver Donating Members
  • Member For: 11y 5m 23d
  • Gender: Male
  • Location: Griffith NSW

Going to be removing the diff hat on the FG turbo ute this weekend to re-seal. Its been leaking from the top of the hat, never dripping in the driveway but always wet with oil over so I'm assuming its coming from the top while I drive.

Any suggestions on gasket goop? new oil? additives? cleaning out the diff? what to check for while I'm there?

Link to comment
Share on other sites

  • Bronze Donating Members
  • Member For: 10y 3m 26d
  • Gender: Male
  • Location: Rockhampton Qld

The permatex red sealant is pretty good. They also make a special green one designed just for diffs. That's not bad if you can find it. Have that on mine and not a drop spilled. Just give it time to cure before you shove oil in there.
While your under there check your diff breather hose isn't cracked/blocked.
Take the Ute for a drive before your drain the diff to get it nice n hot so all the old oil comes out.
No need for additives if you use a decent premium synthetic oil. The penrite stuff below is pretty good for a stock diff. While the covers off you may aswell check for wear on the crown (missing teeth or uneven wear) bbd192ec5c1ac3d7fad0e5ce61b9215a.jpg


  • Like 2
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
  • Create New...
'